Connect with licensed asbestos abatement contractors serving Sherman. Verified state licensing, local notification rules, and transparent pricing.
Get Free QuotesAll asbestos removal work in Sherman must comply with federal NESHAP regulations (40 CFR Part 61 Subpart M) and OSHA standards (29 CFR 1926.1101), as well as Texas state requirements.
Regulations change. Always verify current requirements with the licensing body and notifying agency before beginning any asbestos project.
Cost ranges are sourced from HomeAdvisor national cost data and adjusted for Texas market conditions.
| Project Type | Typical Range |
|---|---|
| Popcorn / Acoustic Ceiling Texture (per sq ft) | $3–$7 |
| Floor Tile & Adhesive (per sq ft) | $5–$12 |
| Pipe Insulation (per linear foot) | $10–$20 |
| HVAC / Duct Insulation | $500–$4,000 |
| Roofing (per sq ft) | $5–$15 |
| Full Home Abatement | $1,400–$9,500 |
Note: Texas near or slightly below national avg; Huntsville/Walker County draws from the Houston metro contractor market; Sherman/Grayson County draws from Dallas-Fort Worth metro contractors. Source: HomeAdvisor. Get free quotes for exact Sherman pricing.
Sherman has approximately 38% of its housing stock built before 1980 (median year built: 1982), when asbestos was widely used. Common Texas housing types include: brick ranch homes, 1950s–1970s suburban development, mid-century commercial, post-war residential.
9×9 and 12×12 vinyl tiles installed before 1980 frequently contain asbestos; the black mastic adhesive beneath them often does too.
Corrugated wrap on steam and hot-water pipes, boiler jackets, and elbow fittings in pre-1980 homes and commercial buildings.
Spray-applied texture and "popcorn" acoustic ceiling products applied before 1978 commonly contain asbestos.
Duct wrap, duct tape, vibration collars, and HVAC insulation in pre-1980 systems often contain asbestos-containing materials (ACM).
Pre-1977 joint compound (drywall mud) and plaster products frequently contain asbestos; sanding disturbs fibers most.
Asbestos-cement shingles, transite siding, and roofing felt were common in residential and commercial construction through the 1970s.
A state-accredited asbestos inspector surveys the property and collects bulk samples for laboratory analysis. Do not disturb suspected ACM before inspection.
Before work begins, the licensed contractor submits notification to Texas Commission on Environmental Quality (TCEQ) and Texas DSHS Asbestos Program; Huntsville/Walker County projects notify TCEQ Region 12 Houston Regional Office and Texas DSHS Asbestos Program at least 10 working days before qualifying renovation or demolition projects; Sherman/Grayson County projects notify TCEQ Region 4 Dallas-Fort Worth Regional Office and Texas DSHS Asbestos Program at least 10 working days before qualifying renovation or demolition projects at least 10 working days in advance for qualifying renovation or demolition projects (40 CFR Part 61 Subpart M; Texas Health & Safety Code §§1954.001–1954.301 (Asbestos Health Protection); 25 TAC Chapter 295).
Workers erect negative-pressure containment, wear HEPA-filtered respirators (NIOSH-approved half-face or full-face APF ≥ 10), and use wet methods to suppress fiber release during removal.
Aggressive air sampling and phase-contrast microscopy (PCM) or transmission electron microscopy (TEM) clearance testing confirms the area meets safe fiber levels before containment is removed.
ACM waste is double-bagged in 6-mil poly bags, labeled per EPA/DOT requirements, and transported to a licensed hazardous waste disposal facility.
Yes. Texas requires Texas Asbestos Contractor License (DSHS); asbestos supervisor and worker certificates required. Unlicensed removal violates state law and can result in significant fines. Always verify contractor license status with Texas Department of State Health Services (DSHS), Asbestos Program.
Small projects (floor tile, ceiling texture) typically take 1–3 days. Full home abatement may take 1–2 weeks. Factor in the 10-working-day advance notification requirement before work can begin.
Typical full-home abatement in Sherman ranges from $1,400 to $9,500. Costs vary by scope, ACM type, and site access. Get multiple quotes from licensed contractors for accurate Sherman pricing.
Homeowners may collect samples, but samples must be analyzed by an accredited laboratory (NVLAP-accredited). For pre-renovation surveys, Texas may require a state-accredited inspector. Do not sand, drill, or disturb suspected ACM before testing.
Encapsulation (applying a sealant or covering ACM in place) is permitted in some situations where the material is in good condition and won't be disturbed. A licensed inspector must assess whether encapsulation is appropriate; notification requirements still apply for qualifying projects.