Connect with licensed asbestos abatement contractors serving Edmonds. Verified state licensing, local notification rules, and transparent pricing.
Get Free QuotesAll asbestos removal work in Edmonds must comply with federal NESHAP regulations (40 CFR Part 61 Subpart M) and OSHA standards (29 CFR 1926.1101), as well as Washington state requirements.
Edmonds is in Snohomish County within the Puget Sound Clean Air Agency (PSCAA) jurisdiction. PSCAA Regulation III §3.07 incorporates and may supplement federal NESHAP notification requirements for qualifying renovation and demolition projects in King, Kitsap, Pierce, and Snohomish counties. Notify both the Washington State Department of Ecology Northwest Regional Office and confirm PSCAA requirements before beginning qualifying projects. State-specific licensing requirements apply.
Regulations change. Always verify current requirements with the licensing body and notifying agency before beginning any asbestos project.
Cost ranges are sourced from HomeAdvisor national cost data and adjusted for Washington market conditions.
| Project Type | Typical Range |
|---|---|
| Popcorn / Acoustic Ceiling Texture (per sq ft) | $3–$7 |
| Floor Tile & Adhesive (per sq ft) | $5–$12 |
| Pipe Insulation (per linear foot) | $10–$20 |
| HVAC / Duct Insulation | $500–$4,000 |
| Roofing (per sq ft) | $5–$15 |
| Full Home Abatement | $1,800–$11,500 |
Note: Washington State abatement costs run 10–20% above national averages; Edmonds/Snohomish County (Seattle north metro) reflects higher Pacific Northwest labor and PSCAA compliance costs. Source: HomeAdvisor. Get free quotes for exact Edmonds pricing.
Edmonds has approximately 42% of its housing stock built before 1980 (median year built: 1977), when asbestos was widely used. Common Washington housing types include: mid-century ranch homes, 1950s–1960s split-levels, post-war residential development, mid-century commercial and light-industrial.
9×9 and 12×12 vinyl tiles installed before 1980 frequently contain asbestos; the black mastic adhesive beneath them often does too.
Corrugated wrap on steam and hot-water pipes, boiler jackets, and elbow fittings in pre-1980 homes and commercial buildings.
Spray-applied texture and "popcorn" acoustic ceiling products applied before 1978 commonly contain asbestos.
Duct wrap, duct tape, vibration collars, and HVAC insulation in pre-1980 systems often contain asbestos-containing materials (ACM).
Pre-1977 joint compound (drywall mud) and plaster products frequently contain asbestos; sanding disturbs fibers most.
Asbestos-cement shingles, transite siding, and roofing felt were common in residential and commercial construction through the 1970s.
A state-accredited asbestos inspector surveys the property and collects bulk samples for laboratory analysis. Do not disturb suspected ACM before inspection.
Before work begins, the licensed contractor submits notification to Washington State Department of Ecology, Northwest Regional Office (Bellevue); Edmonds/Snohomish County projects notify Ecology Northwest Regional Office at least 10 working days before qualifying renovation or demolition projects; Puget Sound Clean Air Agency (PSCAA) Regulation III §3.07 also applies to Snohomish County projects at least 10 working days in advance for qualifying renovation or demolition projects (40 CFR Part 61 Subpart M; WAC 296-65 (Washington Industrial Safety and Health — Asbestos); RCW 49.26 (Asbestos Workers' Protection Act); WAC 173-303 (Ecology Dangerous Waste Regulations, for ACM disposal)).
Workers erect negative-pressure containment, wear HEPA-filtered respirators (NIOSH-approved half-face or full-face APF ≥ 10), and use wet methods to suppress fiber release during removal.
Aggressive air sampling and phase-contrast microscopy (PCM) or transmission electron microscopy (TEM) clearance testing confirms the area meets safe fiber levels before containment is removed.
ACM waste is double-bagged in 6-mil poly bags, labeled per EPA/DOT requirements, and transported to a licensed hazardous waste disposal facility.
Yes. Washington requires Washington State Asbestos Contractor/Consultant License (L&I); certified asbestos supervisor, worker, inspector, management planner, and project designer required. Unlicensed removal violates state law and can result in significant fines. Always verify contractor license status with Washington State Department of Labor and Industries (L&I), Asbestos Certification Program; Washington State Department of Ecology (Ecology) enforces NESHAP.
Small projects (floor tile, ceiling texture) typically take 1–3 days. Full home abatement may take 1–2 weeks. Factor in the 10-working-day advance notification requirement before work can begin.
Typical full-home abatement in Edmonds ranges from $1,800 to $11,500. Costs vary by scope, ACM type, and site access. Get multiple quotes from licensed contractors for accurate Edmonds pricing.
Homeowners may collect samples, but samples must be analyzed by an accredited laboratory (NVLAP-accredited). For pre-renovation surveys, Washington may require a state-accredited inspector. Do not sand, drill, or disturb suspected ACM before testing.
Encapsulation (applying a sealant or covering ACM in place) is permitted in some situations where the material is in good condition and won't be disturbed. A licensed inspector must assess whether encapsulation is appropriate; notification requirements still apply for qualifying projects.